• Todd8452

Christopher1774

I spent half the day in Krakow and I didn't buy that enkamate... You can order it online, but I can't wait to get it done faster. I found an interesting hair tie for a bun in the supermarket in the section where they sell various hairpins and elastics for girls. The approximate size of the holes is about 1.7mm. The material is a bit stiff and elastic.

Robin

The air is being sucked in well, but it's very noisy and the bubbles are quite large (test in fresh water). Do not rely on tests in fresh water.

Karen

But these pumps are made correctly and not expensively, while the gaskets are put on the wrong way.

Melinda2740

Salt a basin of water and test it, or contact Agnieszka since you are in the same city.

Heather6148

Wow! Where can I find Agnieszka?

Jennifer5371

I modified the pump - I glued material from a "hair tie" onto the rotor. The vibration is gone, the noise has decreased significantly, and it sucks in air even better - now the air dropper roars like a tractor (I already made a muffler from a syringe).

Tricia7885

Are you satisfied with the result or will you redo it?

Darlene4238

So far, I like it much more than before. Today, I bought fittings and hoses for connecting the osmosis system. I also bought a three-channel TDS meter that connects to the hoses of the osmosis filters (it measures the water before the filter, after osmosis, and after the last ion exchange cartridge). So now I will set all this up, wait for the water to fill up, and then I will try it out and see if I am satisfied with the results or not.

Christine

I will also try 2000 in the pen with a standard impeller.

Christopher

Enkamate Ready rotors for jebao 2000: It has the option - shipping from England across Europe, delivery is even faster and cheaper. )))

Michael5242

Thank you! But with that price, I'll redo the rotor myself if the foam doesn't work for me.

John3165

Here is the rotor.

Brent7831

I redesigned my impeller (photo). It has been working for a month and a half. It pushes foam well. There is a slight vibration - I made the impeller by hand and I didn't have any lathes or drilling machines, so the alignment is not great...

Jade

I didn't do anything with the rotor. I positioned the pump vertically inside the foam separation column. There's no noise, and there's enough foam. Overall, I'm satisfied.

Monique1236

Did you have the water inlet nozzle for the pump included? (mesh flask) I only had the outlet pipe included...

Stacy6866

There was no net, it was from 3000. But it wasn't needed, I placed the pump in the middle of the foam.

Caitlin3279

My Jebao DC200 pumps (on the skimmer and the overflow) have started to hum over time... At first, there was no sound at all, but now there's a constant even hum. I cleaned them - I thought dirt or salt had stuck to the rotor and caused the vibration - but there's nothing there.

Joe

Remove from maximum power. Place a silicone or foam pad underneath.

Nicole7268

Obvious marriage of pomp. We have a return of DC and noise in the pen - oh.

Michele9664

How strange - at first they were quiet, but then they became noisy...

Rachel9060

It has been working on the return of the used one for a year. Maybe it was assembled incorrectly, or maybe the silicone seal was damaged.

Nicole

It seems like he was collecting everything carefully... Moreover, I didn't interfere with it - it started to hum on its own over time... And during disassembly (when I was cleaning it), everything was in place. In this pump (DC2000), you can adjust the rotor using silicone bushings. I noticed that if these rubber rings are maximally "spread apart," meaning one is fully inserted into the pump body and the other is fully inserted into the pump cover (where the impeller is), it creates a situation where the rotor has axial play between these two bushings, and then it can hum, especially when the rotor is installed not vertically but horizontally or just at an angle.

Tanner

I found a rotor (or rather, an impeller for the rotor) on AliExpress. There is a choice for pumps of 600, 1000, 2000, and 4000. However, no sizes are specified. Will this impeller (of course, I need to choose one for the 2000 pump) fit my Jebao DC-2000 pump? The reason for replacing my homemade impeller is to install a more balanced impeller for a longer pump life and less noise. I have seriously considered buying a new skimmer along with the pump, where everything is set up - the skimmer size for the aquarium plus the required pump.

Andrea

So, no one bought such impellers?

Sheila

I have a Jebao 6000 on return, it doesn't make noise. There is a low-frequency hum when opening the cabinet, probably if I hadn't soundproofed it, the hum would be bothersome, after all, it's a bedroom.

Alejandro

We, like normal people, immediately sent our pumps to the masters. They have CNC machines. They have years of experience making impellers and rotors. By the way, for a small amount of 300-500 hryvnias, it's nothing for Polish earnings. That's what we advised you. You, however, disregarded the advice and tied hair ties somewhere. And now, after six months, you are asking again about the Chinese miracle. There is a Slavic proverb: "Even a fool can break a stick."

Melissa1838

There are a lot of trains to Poland, for 5 euros they will kiss you in the ass if you haven't forgotten.

Stephen5841

At this time, my aquarium, which is already running, works without a skimmer... Additionally, there is no train going to the city I need - it requires a transfer. How would you suggest solving this issue? Should I ask someone to go in the morning to pick up the package, for example, in Lviv, and then send it to Enerhodar in the afternoon...? How do you envision this? And how much will it cost me - everything needs to be paid for - I would rather buy a new branded pump as a whole. How long will all this take? I found a rotor from the Chinese - so I'm asking if anyone has tried it or not - what's wrong with that?

Jennifer5371

My wife has been receiving packages from Slovakia for about five years, with socks and tights. There is a post office in almost every village. And what kind of macarons are you planning to receive from China?

Elijah7048

To modify my rotor, it needs to be sent to a specialist, and during this time, the aquarium will be without a pump. A impeller can be ordered from China; it will arrive slowly, and once it gets here, I can install it. While I will be trimming that impeller to fit the rotor, it will take a couple of hours, and while my rotor is being sent by mail, modified, and returned, the aquarium will be without a pump for 1.5 months.

Joshua8425

Moreover, I am no longer focused on finishing my Chinese pump; I want to buy a good, branded pump with a ready-made impeller for a protein skimmer, but I can't decide which one to choose. Most of them are AC 220 volts rather than DC 12 or 24 volts, and from my limited experience with low-voltage DC pumps, low-voltage ones operate much more quietly than the regular 220-volt ones. Additionally, it can be adjusted electronically without having to reach into the aquarium to change the pump's power. Now I just need to find a branded one with an impeller for the protein skimmer...

Brandi

YOU DO NOT NEED TO SEND THE ROTOR. YOU NEED TO TAKE A FEW PHOTOS, A DIAGRAM OF HOW THE PUMP IS INSTALLED IN THE PENNIK, CONTACT THE MASTER, AND ORDER A GRILLE AND IMPLER (THE THING WHERE AIR MIXES WITH WATER). THE GRILLE AND IMPLER WILL BE SENT TO YOU, AND YOU WILL INSTALL THE ROTOR YOURSELF, PUT IN THE IMPLER, PLUG IT IN, AND GOD HELP YOU.

Rita

When I spoke with the master, I clearly understood that I needed to send him my pump for modification. Maybe we misunderstood each other... But still, I want to buy a branded, high-quality ready-made pump - please suggest good options if you know any.